Universal Astronomics MicroStar.

Offering the same smooth motions as the UniStar, but in a smaller package.
Its compact size gives it greater strength to carry heavier loads up to 12 lbs and then some.
Available in Basic, Deluxe or Super Deluxe model (read below for explaination of the
differences)
Options include Single or Dual Adjustable Guide Handles, Quick setup Eyepiece Tray,

Basic or Deluxe?

These descriptions pertain to UniStar, UniStar Light, MicroStar and MacroStar which are all
available as Basic, Deluxe or Super Deluxe.

The Basic models are comprised of a long flat plate with a slot cut fore and aft to accept
thumbscrews for mounting typical tube rings. Because there are no means to attach anything
near the center of the plate, scopes with clamshell-type tube rings or a single camera tripod
mounting hole, require our Clamshell Adapter Plate which attaches to the scope then allows
attaching to the Basic model with thumbscrews. The benefit of this accessory is that it
provides 2" of balance travel as it is designed to slide back-and-forth in the slots that are cut
into the Basic Head.

The Deluxe models are a Saddle/Plate system. The scope requires a male dovetail mounting
plate (or rail) attached to it and can then attach to the Deluxe Head which has a female
dovetail saddle design. This allows for quick installation and removal of the optics, as well as
allows for balancing the optics for and aft. The amount of travel for balance is dependent on
the length of the mounting plate. The UniStar Light and MicroStar Deluxe heads hold the
plate with a single clamping knob and is designed to hold rails from 1.5-2.25" wide. This
includes Vixen, Orion, Celestron, Meade (these are all Synta rails from China), Astro-
Physics, etc, and our own 2" saddle plate.

The MicroStar or UniStar Light Super Deluxe incorporates the saddle design reserved for the
larger UniStar/MacroStar Deluxe (description can be found in the next paragraph). Its a $50
upgrade from the standard Light Deluxe head. The advantages of this design is that the
moveable jaw is non-marring, but its largest benefit is its ability to accept any dovetail plate
between 1.5-3.25" wide.

The larger UniStar Deluxe incorporates a moving jaw on one side that clamps the saddle
plate with a single handknob. This is available with a choice of either our 2" or 3" Jaw. Which
one to choose can typically depend on the equatorial mount that the UniStar may share duty
with or if the scope has a particular dovetail plate of its own. If neither of these factors pertain,
then the customer can choose the saddle/plate based on the size of the scope. Best
recommendation is that for over 15 lbs, the 3" jaw will carry the load better. The 2" jaw will
carry all the rails listed above, the 3" jaw will carry Losmandy, Astro-Physics and Celestron's
wider plate, etc, and our own 3" plate. Even if only one jaw size is required, purchasing both
jaws (£25.00 additional) allows many benefits in that it will allow the UniStar mount to accept
any dovetail rail between 1.5-3.25" which means no future problems with EQ mount
compatability. And it will also ensure easy resale in the future as the mount will not be
restricted to compatibility with only certain EQ mounts. UniStar Light and MicroStar can be
upgraded to this head, its actually a necessity if you are trying to use a 3" mounting plate, or
if you prefer the non-marring design of the clamping jaw rather than the clamping screw.

Prices:
01501 MicroStar Basic (10 lb capacity, 2x8 plate for mounting tube rings) - £149.00
01502 MicroStar Deluxe (10 lb capacity, 2” dovetail saddle) - £229.00
01503 MicroStar Super Deluxe (10 lb capacity, includes UniStar Deluxe Saddle) - £279.00

All plus £10.00 shipping and insurance.

The Astronomy Shop

1 Tone Hill. Wellington

Somerset TA21 0AU

United Kingdom

Telephone: +44 (0)1823 665510